Wagner Paint Crew Airless Sprayer Repair Part 2.mp4

Tricks, Ratschläge, Online, Reparieren, Landwirtschaft, Landwirtschaft Maschine

1. need help my 2200 wagner paint sprayer sound like its dying it usually sounds loud not working
2. hy i can t unscrew the nylon screw or what it is,do you have any ideea how to unscrew it?thank you!
3. Perfect just exactly the info I needed
4. My wagner crew 770 paint sprayer will only prime and not go in to spray mode could this be my outlet valve
5. Thanks for the video! Mine just started acting up today after being in storage. The motor will not shut off when pressure has built up like it used to and paint started just spattering out. Going to do a tear down like you did.
6. can you share me Wagner Finish 350 or 370 maintenance/repair?
7. WOW, that was alot better than the last clean up video I watched. It really helps to have taken apart the machine before,use the right tools and know what the parts are called. Very helpful.Maybe next time go into more detail, But a very helpful video. Now I just need a place to get the parts. Thanks.
8. Very good video! I unfastened and white piece of plastic is cracked at the bulb at the bottom and no longer grab the plunger! In this situation, you will find this piece of plastic, and where I could find it! and bearing from me is a little worn, can draw some balls! In waiting for an answer!
9. Did u change the spring, ball bearing, and seat, or just took it apart and cleaned it?  My gun is spitting paint when I release the trigger.  
   
   thanks
10. Any luck finding a spring plate????
11. awesome mate. l always pull the unit apart now. My problem was the prime / spray unit nob. pull the pressure  switch cover off (4 small screws) then remove the  shaft and spring .  clean shaft and grease ,. it will have paint build up . Then remove the (red)  prime / spray  shaft (remove from the back of the nob and repeat the process.
12. hi I wonder iff you can help.....after cleaning my paint crew I think I strained the machine by pushing lots of water through it whilst cleaning it suddenly had a loud knocking sound  the pressure decreased and Im wondering what the problem is and how I can fix it ?
13. I have owned several of these and found the $.10 O rings are usually the problem with it not priming.  If the little oring in the outlet valve is nicked the whole unit is worthless. I'd like to know where to find the right size O rings so I have a spare set at all times. Very frustrating to have an entire job set up, paint in the tray and have a $.10 O ring fail..  Shame on Wagner for not supplying an extra set. Would cost them pennies.
14. To remove the inlet valve find the white plastic tool attached to the base of the pump assembly.  It looks like a small hexagon block of white plastic with a square hole in the center with two thumb taps on top to help turn it.  Insert this into the inlet valve opening and turn it with a 3/8" ratchet extension.  turn it counter clockwise and pull it out through the paint tub.  Or as in the video it can be removed after you take the paint tub off.
15. How do you remove the inlet valve?
16. Has anybody had luck using their Wagner 770 to spray CWF Cedar stain on their deck?  I don't know why it wouldn't work for lattice and such, but I wanted to ask.
17. Wher are part 1.  can't find it..
    
    what are you putting dawn  first  before  the  litke  stel ball   
18. very helpfull - but wont fix whats wrong with mine.  =( used twice
19. Great video!! Is there a Part 1?
20. This is a great Video.  Thank you.   I almost threw my paint crew out the window until I found your video.   However.  you downplayed the importance of the "Outlet Valve".   There are three (3) "O" rings on this device.   1 - big one around the shaft, 1 - small one at the tip, and the most important one is inside the "Outlet Valve" at the tip.  There are 4 little notches at the end of the valve.  Those notches are to grab with a small set of needle nose pliers and pulls the cap from the tip of the unit.  The third "O" ring is at the tip of the spring check.  If this spring check "O" ring is damaged, it will allow the unit to prime, but not build pressure.